Ghost 2 Immobiliser Reviews
The Ghost 2 immobiliser utilizes cutting-edge technology to prevent car theft. This hidden device is not detected by thieves and only starts your engine when an app or PIN code is entered.
It connects to the CAN data network of your vehicle and is weatherproof. It comes with a service/valet feature that allows you to temporarily start your vehicle while it is in garage.
Easy to install
The Ghost immobiliser guards your vehicle from theft of keys, cloning and hacking. It utilizes a unique PIN code system that is integrated into the ECU of your vehicle, making it difficult for thieves to identify or alter. In contrast to traditional immobilisers, it does not require any special keys or sensors and is completely hidden from view with no LEDs or signals that signal its presence. It is also less expensive than replacing an ECU or installing the new key fob. Additionally, it can reduce your monthly insurance premiums.
When installing a Ghost 2 immobiliser, be sure to follow the instructions of the manufacturer carefully. This will ensure that the device works correctly and effectively. After the installation is completed check the system by entering the PIN code and then starting the engine. Regular testing will allow you to identify any issues before they become worse.
Make sure you check the position of CAN H and L wires prior to starting the installation. They are essential for powering the immobiliser so it is vital to connect them correctly. Labeling the wires will make it easier to find them when installing. Once you have identified the locations of these wires, connect them to a constant 12V power source as well as a grounding point. Use the fuse tap to safeguard the connections against short-circuits or damage.
After connecting the wires, tidy the wiring using cable ties to avoid potential tampering. You can also cover the connections with insulation tape or heat-shrink tubing. This will shield the device from electrical shorts and will extend the life of the device. It's a great idea to test your Ghost 2 immobiliser once the wiring has been secured.
The Ghost 2 immobiliser offers a service mode in situations where you may have to give your vehicle away for example, when it is being repaired or valet-parked. This disables the PIN sequence temporarily. To activate this feature, press the brake pedal while holding down the accelerator for a number of times equal to the first digit of the emergency code. The system will enter service mode. This is confirmed by flashing 5 times the indicator signal.
It is simple to change PIN codes
Ghost 2 immobilisers are an excellent way to safeguard your car from thieves. It is installed discreetly inside the vehicle and is only accessible through a specific code. The device communicates directly with the vehicle ECU via its data bus, and does not use radio frequency signals like traditional Thatcham immobilisers or aftermarket alarm systems. This makes it harder for thieves to hear the click of an immobiliser relay, or add new keys. The control unit is concealed in the wiring harness or dashboard, and cannot be physically altered to reset the system.
The ghost 2 immobiliser is connected to your vehicles CAN Data network and makes use of the buttons already present on the steering wheel, door panels and centre console to create an individualised sequence of up to 20 button presses which must be entered before the engine can begin as it would with a PIN code. This unique next generation system does not require any wire cutting upon installation and can be fully reprogrammed at any time. You can even start your vehicle in Service or Valet mode when you hand it to a mechanic to complete the work.
You can also make use of the app to alter your PIN code, or deactivate it completely if you have lost your keys. This feature is particularly useful in the event that you've lent your car away to someone else to use for parking or valet service. It will stop them from starting it and driving it away without your consent. It is also undetectable to professional thieves because it does not make use of circuit cuts or radio frequencies.
The ability of the immobiliser to protect against relay thefts is another important feature. Relay theft is one of the most popular methods of car theft. Criminals gain access to your car's diagnostic ports, then modify the signal sent by the car's ECU to fool it into thinking that the car's key is valid and present. This is the way traditional immobilisers are bypassed, but with the ghost 2 immobiliser the signal is blocked before it reaches the ECU.
Simple to use app
Ghost 2 is an immobiliser that is revolutionary. It safeguards your vehicle from key-cloning. It works by connecting to the CAN data network of your vehicle and asking you to enter a PIN code before it will start the engine. It also stops thieves from using signal spoofing and device spoofing, both of which are common techniques used to steal vehicles.
The system is easy to use and works like an ordinary auto alarm. Once you have installed it, you can generate a unique PIN code sequence of up to 20 digits in length and must be entered before the vehicle is started. This will protect the vehicle from being taken even if your keys are stolen. If you wish to disable the system, you can do so via an app on your smartphone.
The ghost is silent and does not emit radio frequency signals. It is a weatherproof, discreet device that can be installed in any vehicle. It can be concealed under the dash, steering wheel, or on the door panels. It communicates with your ECU over the CAN data circuit and is not affected by diagnostic tools that thieves use to find security systems. It is not affected by jamming devices which disguise codes.
It is a concealed installation that does not require any wire cutting or modifications to the car and can be used as an anti-theft system for all cars. Its technology has been proven efficient, and it's in compliance with TASSA Standards. The ghost is a fantastic solution for classic, sports and prestige automobiles, and can also be used to secure vehicles that are being let out on websites like Turo.
The Autowatch Ghost 2 is the next generation in car immobilisers. The system is inaccessible to thieves, and prevents them starting your vehicle without your PIN, or unless they are authorized by the app. It doesn't emit radio frequencies or any other signals that scanners detect. The installation process is easy and quick. The app comes with a simple interface and a simple navigation. how much is a ghost immobiliser has an GPS tracker that will help police locate the vehicle and then recover it.
Simple to reset
Ghost 2 immobilisers are a great way to protect your car from being stolen. It integrates into your vehicle's ECU creating a wall that thieves are unable to penetrate without the right pin. It's also TASSA-certified that means it's acknowledged by insurance companies. It is a powerful tool to prevent car theft and could save you money in the long run.
The Ghost system unlike traditional alarms or immobilisers, which require cutting circuits and is directly connected to the vehicle's CAN data network. It operates by using the buttons on your dashboard and steering wheel. You can create a unique PIN that is up 20 presses long. This PIN has to be entered before the engine can start, just as with a credit card PIN. Ghost is unnoticeable to thieves and has no indicators that signal its presence and makes it the most reliable aftermarket CAN bus immobiliser that is on the market currently.
Another benefit of the Ghost system is that it doesn't utilize radio frequency signals, which means it isn't scannable or intercepted by thieves. This prevents cloned keys and relay attacks, as well as the more popular method of hacking into a car's CAN bus system by looking for signals from the alarm/immobiliser. The Ghost system is designed so that it is able to be hidden inside your vehicle. There are no LEDs or other signals to signal its presence.
The system also comes with an option for a Transport Mode that disables the Ghost system that is helpful in situations in which you have to temporarily disable it, such as during transportation or servicing. This mode is less effective than Service Mode as it doesn't disable the Ghost system when you exceed 31 mph within 15 minutes.
You'll require the emergency code provided by your installer to reset your Ghost 2 immobiliser. The code is typically hidden beneath the scratch-off portion of the card provided with your installation. You should keep this emergency code safe and store it in a safe place that is secure, such as your wallet at home.